Search Results

This paper is the fourth in a series describing work sponsored by the Bureau of Mines to reduce diesel particulate and gaseous emissions through fuel modification. A stabilized water microemulsion fuel developed in previous work was tested in a Caterpillar 3304 NA four-cylinder engine with compression ratio and injection timing and rate optimized for this fuel to demonstrate the emissions reductions achieved. It was tested in both standard and optimum configurations with both baseline DF-2 and optimized microemulsion fuels. Gaseous and particulate data are presented from steady-state tests using a computer-operated mini-dilution tunnel and from transient tests using a total exhaust dilution tunnel. The optimized engine-fuel combination was effective in reducing particulates and oxides of nitrogen in steady-state tests. However, the standard engine-fuel combination provided the lowest particulate and NOx emissions in transient tests.

The increased use of diesel-powered equipment in underground mines has prompted interest in reducing their exhaust pollutants. Control of particulate emissions without substantial penalties in other emissions or fuel consumption is necessary. This paper describes test results on a prechaaber, naturally-aspirated, four-cycle diesel engine in which two different concentrations of water-in-fuel emulsions were run. The independent variables comprising the test matrix were fuel, speed, load, injection timing, injection rate, and compression ratio. The dependent variables of the experiment included particulate and gaseous emissions and engine thermal efficiency. Regression analysis was performed on the data to determine how particulate emissions were affected by fuel and engine parameters. Results of this analysis indicated that substantial reductions in particulate emissions could be obtained by utilizing water-in-fuel emulsions.

A technique is verified for mapping the exhaust emission levels of a diesel engine during transient operation. Particulate matter, oxides of nitrogen, hydrocarbons, and carbon monoxide emissions were sampled for discrete segments of various transient cycles. Each cycle consisted of four distinct segments. The discrete segments are described by average engine conditions, rate of change variables, and segment length. Regression analysis was used to develop equations relating the emission levels during each segment to the engine parameters. The regression equations were then used to obtain estimates of composite emission levels of several complex transient cycles that were subsequently tested. These cycles included the EPA heavy-duty transient cycle and two simulated heavy-duty cycles developed for underground mine vehicles. Comparison of the predicted and measured cycle emissions are made for the EPA heavy duty cycle and the simulated mine cycles.

Mixtures of methanol, water and heavier alcohols, simulating “raw’ methanol at various levels of processing, were tested in a constant volume combustion apparatus (CVCA) and in a single-cylinder, direct-injection diesel engine. The ignition characteristics determined in the CVCA indicated that the heavier alcohols have beneficial effects on the auto-ignition quality of the fuels, as compared to pure methanol. Water, at up up to 10 percent by volume, has little effect on the ignition quality. In all cases, however, the cetane numbers of the alcohol mixtures were very low. The same fuels were tested in a single cylinder engine, set-up in a configuration similar to current two-valve DI engines, except that the compression ratio was increased to 19:1. Pure methanol and five different blends of alcohols and water were tested in the engine at five different speed-load conditions.

Autoignition of coal-water-slurry (CWS) fuel in a two-stroke engine operating at 1900 RPM has been achieved. A Pump-Line-Nozzle (PLN) injection system, delivering 400mm3/injection of CWS, was installed in one modified cylinder of a Detroit Diesel Corporation (DI)C) 8V-149TI engine, while the other seven cylinders remained configured for diesel fuel. Coal Combustion was sustained by maintaining high gas and surface temperatures with a combination of hot residual gases, warm inlet air admission, ceramic insulated components and increased compression ratio. The coal-fueled cylinder generated 85kW indicated power (80 percent of rated power), and lower NOx levels with a combustion efficiency of 99.2 percent.

Four major coal fuel projects which were performed at Southwest Research Institute over the past ten years are reviewed. Beginning with the “Alternative Fuels for Highway Utilization” project in 1979, and the success of carbon-black/diesel fuel slurries, the development of the coal slurries is traced to the current technology. Most recently, full-scale locomotive engines have been operated on 50% coal in water slurries at thermal efficiencies approaching that of diesel fuel performance. The paper is concluded with a recommended engine design for coal slurries.

During the 1980's, vegetable oils, microemulsions containing fatty alcohols as surfactants, and fatty esters have been extensively investigaed as alternative fuels to #2 diesel fuel (DF-2) used in farm tractors. Despite the importance of vegetable oils (mainly triglycerides) and fatty derivatives to the alternative fuel program, cetane numbers for pure triglycerides and many fatty derivatives were not reported. In the current study, estimated cetane numbers of these materials have been determined by use of a constant volume combustion bomb. Prior research has shown that this equipment can produce cetane numbers that correlate satisfactorily with engine cetane numbers as determied by ASTM D 613. The influence of chemical structure on ignition delay and cetane number was investigated. Evidence is presented that shows the current cetane number scale is not always suitable for these fatty materials. Suggestions are made as to what might be done to remedy this problem.

Biodiesel is a mixture of esters (usually methyl esters) of fatty acids found in the triglycerides of vegetable oils. The different fatty compounds comprising biodiesel possess different ignition properties. To investigate and potentially improve these properties, the cetane numbers of various fatty acids and esters were determined in a Constant Volume Combustion Apparatus. The cetane numbers range from 20.4 for linolenic acid to 80.1 for butyl stearate. The cetane numbers depend on the number of CH2 groups as well as the number of double bonds and other factors. Various oxygenated compounds were studied for their potential of improving the cetane numbers of fatty compounds. Several potential cetane improvers with ignition delay properties giving calculated cetane numbers over 100 were identified. The effect of these cetane improvers depended on their concentration and also on the fatty material investigated.

The key feature of diesel fuel ignition quality is ignition delay time. In the American Society for Testing and Materials standard test for cetane number measurement, (ASTM D 613) the ignition delay time is held constant while the compression ratio is varied until ignition occurs at the set time. On the other hand, commercial diesel engines have set compression ratios and therefore, the ignition delay time varies with the cetane number of the fuel. The shorter this delay time, the wider the time window over which the combustion processes are spread. This leads to a more controlled heat release rate and pressure rise, resulting in prevention of diesel knock and in lowering of emissions. High cetane fuels exhibit short ignition delay times. The Constant Volume Combustion Apparatus (CVCA) precisely measures the ignition delay time of fuels. This study investigates the CVCA as a supplementary tool for characterization of diesel fuel ignition quality under a variety of conditions.

This paper reports on the third part of a continued study (SAE Papers 961182, 971636) to develop the Ignition Quality Tester (IQT™). Past research has shown that this automated laboratory/refinery apparatus can be used to accurately predict the cetane number of middle distillates and alternative fuels using small sample volumes (< 50 mL). The paper reports on the main objective of a study performed by Advanced Engine Technology Ltd. (AET), in co-operation with its research partners. The primary research objective of this work is to further the understanding of fuel preparation (fuel air mixing) and start of combustion processes in the IQT™. Key to this understanding is the manner in which single molecule compounds and full boiling-range diesel fuels behave during these processes. Insights are provided into the manner in which the American Society for Testing and Materials (ASTM) D-613 primary reference fuels (PRFs) undergo fuel preparation and start of combustion in the IQT™.